Table of Contents
Hewlett-Packard's implementation of supplementary groups is nonstandard (for
historical reasons). There are two group files,
/etc/logingroup; the system maps UIDs to numbers using the former, but
initgroups() reads the latter. Most system admins who know the ropes
(hard-link does not work for reasons too obtuse to go into here). initgroups() will complain if one of the
groups you're in, in
/etc/logingroup, has what it considers to be an invalid
ID, which means outside the range
60000 currently on HP-UX. This precludes -2 and 65534, the usual
If you encounter this problem, make sure the programs that are failing to initgroups() are run as users, not in any groups with GIDs outside the allowed range.
This is documented in the HP manual pages under setgroups(2) and passwd(4).
If you run an old version of SCO UNIX, you may need to get important TCP/IP patches for Samba to work correctly. Without the patch, you may encounter corrupt data transfers using Samba.
The patch you need is UOD385 Connection Drivers SLS. It is available from SCO ftp.sco.com, directory SLS, files uod385a.Z and uod385a.ltr.Z).
The information provided here refers to an old version of SCO UNIX. If you require binaries for more recent SCO UNIX products, please contact SCO to obtain packages that are ready to install. You should also verify with SCO that your platform is up to date for the binary packages you will install. This is important if you wish to avoid data corruption problems with your installation. To build Samba for SCO UNIX products may require significant patching of Samba source code. It is much easier to obtain binary packages directly from SCO.
DNIX has a problem with seteuid() and setegid(). These routines are needed for Samba to work correctly, but they were left out of the DNIX C library for some reason.
For this reason Samba by default defines the macro NO_EID in the DNIX section of includes.h. This works around the problem in a limited way, but it is far from ideal, and some things still will not work right.
To fix the problem properly, you need to assemble the following two
functions and then either add them to your C library or link them into
Samba. Put the following in the file
.globl _setegid _setegid: moveq #47,d0 movl #100,a0 moveq #1,d1 movl 4(sp),a1 trap #9 bccs 1$ jmp cerror 1$: clrl d0 rts
Put this in the file
.globl _seteuid _seteuid: moveq #47,d0 movl #100,a0 moveq #0,d1 movl 4(sp),a1 trap #9 bccs 1$ jmp cerror 1$: clrl d0 rts
After creating the files, you then assemble them using
which should produce the files
Next you need to add these to the LIBSM line in the DNIX section of the Samba Makefile. Your LIBSM line will look something like this:
LIBSM = setegid.o seteuid.o -ln
You should then remove the line:
from the DNIX section of
By default during installation, some versions of Red Hat Linux add an
/etc/hosts as follows:
127.0.0.1 loopback "hostname"."domainname"
This causes Samba to loop back onto the loopback interface. The result is that Samba fails to communicate correctly with the world and therefore may fail to correctly negotiate who is the master browse list holder and who is the master browser.
Corrective action: Delete the entry after the word "loopback" in the line starting 127.0.0.1.
Disabling sequential read ahead using
vmtune -r 0 improves
Samba performance significantly.
Some people have been experiencing problems with F_SETLKW64/fcntl when running Samba on Solaris. The built-in file-locking mechanism was not scalable. Performance would degrade to the point where processes would get into loops of trying to lock a file. It would try a lock, then fail, then try again. The lock attempt was failing before the grant was occurring. The visible manifestation of this was a handful of processes stealing all of the CPU, and when they were trussed, they would be stuck in F_SETLKW64 loops.
Please check with Sun support for current patches needed to fix this bug. The patch revision for 2.6 is 105181-34, for 8 is 108528-19, and for 9 is 112233-04. After the installation of these patches, it is recommended to reconfigure and rebuild Samba.
Thanks to Joe Meslovich for reporting this.
Nsswitch on Solaris 9 refuses to use the Winbind NSS module. This behavior is fixed by Sun in patch 112960-14.